Conversion Guidelines

THE OPEL MOVANO CONVERSION GUIDELINES

The Opel Movano has many faces – and it adapts to an enormous range of requirements more easily than almost any other Opel commercial vehicle. Opel has published these guidelines to help bodybuilders with the various stages of conversion. You will find all the relevant information below as PDF downloads.

Here are all the facts you need. Just one click and you’ll find practical guidelines with all the technical data on standard sections, chassis versions, additional information and electronics.

Content Part 1-3

GENERAL POINTS, VEHICLE INFORMATION

 

  • BODYWORK RANGE
  • ENGINE / GEARBOX RANGE
  • VEHICLE IDENTIFICATION
  • CAB SEPERATING PARTITION
  • LASHING POINTS ON PANEL VAN
  • ROOF RACKS AND ROOF BARS
  • TRAILER HITCH
  • TYRES AND TURNING CIRCLE/ SPARE WHEEL
  • SUSPENSIONS/ BRAKING/ REAR WHEEL FREE TRAVEL
  • FUEL SUPPLY SYSTEM
  • EXHAUST SYSTEM
  • SEATS AND SEATBELTS
  • MIRRORS
  • SCR-SYSTEM (UREA)

 


DIMENSIONS AND WEIGHTS

 

  • REFERENCE GUIDE / DIMENSION / EXTERIOR LIGHTNING
  • DIMENSIONS OF LOADING AREAS / REAR DOORS / SLIDING DOORS
  • WEIGHTS
  • DETERMINING THE CENTRE OF GRAVITY
  • DETERMINING THE CENTRE OF GRAVITY BY MEASURING AND CALCULATION
  • GROUND CLEARANCE

 


CONVERSIONS LIMIT AND CALCULATIONS

 

  • CONVERSION LIMITS AND ESP
  • OPENING PANELS
  • DASHBOARD
  • AIRBAG

Content Part 4-6

ELECTRICS / ELECTRONICS

 

  • WIRING INSTALLATION / ELECTRICAL CONNECTIONS
  • PASSENGER COMPARTMENT FUSE RELAY BOX
  • STANDARD BATTERY / TERMINALS / ADDITIONAL BATTERY
  • CAN-BUS
  • AVAILABLE CURRENT
  • DASHBOARD
  • START / STOPP
  • OPENING PANELS
  • PARKING BRAKE
  • CAN-BUS INTERFACE MODULE FOR CONVERSIONS, OPTION KC6
  • ELECTR. INTERFACE FOR CONVERSIONS / ACCELERATED IDLE / TACHOGRAPH
  • ENGINE RUNNING INFORMATION
  • EXTERIOR LIGHTNING / DAYTIME RUNNING LIGHT
  • INTERIOR LIGHTNING
  • WIRING PRE FIT FOR TRABUS
  • CRUISE CONTROL / SPEED LIMITER
  • REMOTE ENGINE START / STOPP

 


DESIGN STRUCTURE, GLAZED / SOLID PANELS

 

  • DESIGN STRUCTURE
  • DRILLING AREAS FOR BULKHEAD / FLOORS
  • ROOF CUT OUTS
  • CHASSIS CAB, INSTALLATION OF A BODY
  • PLATFORM CAB, POSITION OF CONNECTIONS ON BODY
  • AIR EXTRACTION IN CABIN AND LOADING AREA
  • PROHIBITED CONVERSIONS



MECHANICAL CONVERSIONS

 

  • ENGINE POWER TAKE-OFF: OPTION V66
  • GEARBOX POWER TAKE-OFF: OPTION M1F
  • FUEL TANK FILLER PIPE
  • HEATING / AIR CONDITION
  • COLD REGIONS
  • LIFT TAILGATE
  • INTEGRATED STEP ON PANEL VAN ON REAR END
  • CHERRY PICKER

Content Part 7

Drawings


HOLE PATTERN OF LOADING AREA-SIDE PANEL

 

  • Side panel of panel van L1H1 - FWD
  • Side panel of panel van L1H2 – FWD
  • Side panel of panel van L2H2 – FWD
  • Side panel of panel van L3H2 – FWD
  • Side panel of panel van L3H2 - RWD
  • Side panel of panel van L4H2 - RWD



BODY SURFACE FOR DECALS

 

  • Bonnet and driver- respectively passenger door
  • Rear doors roof height H1
  • Rear doors roof height H2
  • Side view of panel van L1H1 - FWD
  • Side view of panel van L1H2 – FWD
  • Side view of panel van L2H2 – FWD
  • Side view of panel van L3H2 – FWD
  • Side view of panel van L3H2 – RWD
  • Side view of panel van L4H2 - RWD